RigoSharon
LIVING REEFS INTERN
hey marcus ..heres a info about how to cure live rock..method A, and B..i hope this helps
Curing Live Rock
Important: Do not place uncured live rock directly into an aquarium containing fish, corals, or other marine animals.
Note: Be sure to use gloves when handling live rock to prevent accidental cuts and potential infection.
There are many different ways to cure live rock, however, at Drs. Foster & Smith we have found the following methods to be the most effective:
Method A: Curing process of live rock for the established display aquarium that already contains fish, corals, or any other marine animals.
Place the live rock in a new 30-gallon plastic garbage can. Consider adding bottom drains to the container to speed draining and water changes.
Completely cover the rock with freshly mixed saltwater, with a specific gravity of 1.021 - 1.025.
Use a heater and keep the water temperature near 80 degrees to speed die off.
Provide constant water movement with a power head or air stone.
Keep the area dimly lit to prevent algae blooms.
Perform 100% water changes twice weekly.
Gently scrub the rock with a new nylon bristle brush or toothbrush between water changes to remove any white film or dead material.
When the water conditions stabilize and ammonia and nitrite tests are zero, the rock is ready to be placed into the display aquarium.
Most live rock will be fully cured in 1 - 3 weeks, at which time it is safe to add to the display aquarium.
Method B: Curing process of live rock for the new aquarium that DOES NOT contain fish, corals, or any other marine animals.
Live rock may be used to cycle a new marine aquarium. Follow the manufacturer's directions on the installation of all filtration devices and accessories. Fill aquarium with freshly mixed saltwater with a specific gravity of 1.023-1.025. Activate all filtration equipment, check for leaks, and set heater and/or chiller to the desired temperature of 72-78°F.
Note: Mechanical filtration will need frequent cleaning during this cycling process.
Rinse each piece of live rock in a small bucket of saltwater to remove any loose organic matter, debris, or sand.
Place live rock into the aquarium to create a stable foundation for corals or decorations.
Keep the lighting system off during the cycling period in order to reduce the likelihood of undesirable algae growth.
Gently scrub the rocks periodically with a new nylon bristle brush or toothbrush to remove loose white film or dead material.
Perform 50% water changes weekly while siphoning out any organic matter and loose debris that accumulates at the bottom of the aquarium.
Measure and monitor the ammonia and nitrite levels in the aquarium weekly.
When both ammonia and nitrite levels are zero, perform a 50% water change on the aquarium.
After 24 hours, check the pH of the water and adjust as needed to achieve the desired level of 8.1-8.4.
Most aquariums will cycle within 2-4 weeks using this technique, depending on the equipment that is installed.
Curing Live Rock
Important: Do not place uncured live rock directly into an aquarium containing fish, corals, or other marine animals.
Note: Be sure to use gloves when handling live rock to prevent accidental cuts and potential infection.
There are many different ways to cure live rock, however, at Drs. Foster & Smith we have found the following methods to be the most effective:
Method A: Curing process of live rock for the established display aquarium that already contains fish, corals, or any other marine animals.
Place the live rock in a new 30-gallon plastic garbage can. Consider adding bottom drains to the container to speed draining and water changes.
Completely cover the rock with freshly mixed saltwater, with a specific gravity of 1.021 - 1.025.
Use a heater and keep the water temperature near 80 degrees to speed die off.
Provide constant water movement with a power head or air stone.
Keep the area dimly lit to prevent algae blooms.
Perform 100% water changes twice weekly.
Gently scrub the rock with a new nylon bristle brush or toothbrush between water changes to remove any white film or dead material.
When the water conditions stabilize and ammonia and nitrite tests are zero, the rock is ready to be placed into the display aquarium.
Most live rock will be fully cured in 1 - 3 weeks, at which time it is safe to add to the display aquarium.
Method B: Curing process of live rock for the new aquarium that DOES NOT contain fish, corals, or any other marine animals.
Live rock may be used to cycle a new marine aquarium. Follow the manufacturer's directions on the installation of all filtration devices and accessories. Fill aquarium with freshly mixed saltwater with a specific gravity of 1.023-1.025. Activate all filtration equipment, check for leaks, and set heater and/or chiller to the desired temperature of 72-78°F.
Note: Mechanical filtration will need frequent cleaning during this cycling process.
Rinse each piece of live rock in a small bucket of saltwater to remove any loose organic matter, debris, or sand.
Place live rock into the aquarium to create a stable foundation for corals or decorations.
Keep the lighting system off during the cycling period in order to reduce the likelihood of undesirable algae growth.
Gently scrub the rocks periodically with a new nylon bristle brush or toothbrush to remove loose white film or dead material.
Perform 50% water changes weekly while siphoning out any organic matter and loose debris that accumulates at the bottom of the aquarium.
Measure and monitor the ammonia and nitrite levels in the aquarium weekly.
When both ammonia and nitrite levels are zero, perform a 50% water change on the aquarium.
After 24 hours, check the pH of the water and adjust as needed to achieve the desired level of 8.1-8.4.
Most aquariums will cycle within 2-4 weeks using this technique, depending on the equipment that is installed.